Knauf Home Energy Audit Nationwide

Knauf Home Energy Audit in Los Angeles: What to Know First

We provide independent Knauf home energy audit in Los Angeles, typically completing the full diagnostic and written report within a single visit. Most audits run $280-$450 for a single-family home under 2,500 square feet, and we deliver a written price before any work starts - no exceptions. This page is for Knauf product owners in Los Angeles who need a blower-door test, thermal imaging inspection, insulation inspection, or duct leakage test to find where conditioned air is escaping. Call (628) 226-1097 for a free estimate, or text us if you prefer.

Call (628) 226-1097

How Knauf Products Fail - and How We Fix Them

• Knauf EcoSeal Plus gaps at top plates and rim joists. The water-based elastomeric sealant shrinks 15-20% during cure in dry Los Angeles conditions, leaving hairline channels at the double-top-plate interface in 1960s ranch homes. We pull back the existing Knauf batt, re-seal with compatible acrylic-urethane hybrid, then reinstall to manufacturer density.
• Knauf Jet Stream Ultra blown-in settling in unvented attics. The high-velocity application packs well in open blow, but in Los Angeles’s dense Leimert Park corridor, installers often skip vent chutes above soffit-restricted eaves. The product settles 2-3 inches below the joist crown within 18 months, creating a thermal bypass. We measure settled depth with a probe, calculate the shortfall in R-value, and re-blow to spec with proper venting.
• Knauf Insulation Board (KIB) thermal bridging at knee walls. The 2-inch polyiso-faced boards, common in Silver Lake ADU retrofits, lose adhesion at the foil facing when attic temperatures exceed 140°F - routine in Los Angeles September heat. We find the delamination with FLIR imaging, remove the failed board, and re-secure with mechanical fasteners plus compatible foam sealant rather than relying on adhesive alone.
• Knauf Momentum duct wrap compression at sharp bends. The 1.5-pound density fiberglass wrap, specified for flex-duct transitions, gets over-tightened with zip ties at 90-degree elbows. Compressed to half thickness, it performs at R-2 instead of R-6. We document the compression with caliper measurements, replace with properly tensioned wrap, and add support saddles to prevent recurrence.
• Knauf Ecobatt with ECOSE Technology moisture retention near bathroom vents. The plant-based binder is hydrophilic during the first 90 days after installation. In Los Angeles homes where the prior installer terminated the bath fan into the attic rather than through the roof, we’ve found Ecobatt weighing 40% above spec at the vent termination. We relocate the exhaust, replace the water-affected batts, and seal the penetration with fire-rated foam.

Our Knauf Home Energy Audit Process

1. 1
   Call and schedule. A live person answers 24/7. We confirm your Knauf product type if you know it, and we text you when your technician is en route.
2. 2
   Blower-door test first. We pressurize the house to 50 Pascals and record the CFM50 reading - the single number that tells us how much air your envelope is leaking before we open the attic hatch.
3. 3
   Thermal imaging and physical inspection. FLIR scan of all Knauf-insulated surfaces, plus probe measurements of settled blown-in depth and batt compression. We photograph every finding.
4. 4
   Duct leakage test if indicated. We seal the registers and run a Duct Blaster to quantify how much conditioned air is escaping into unconditioned space - a separate number from the envelope leakage, and equally important.
5. 5
   Written scope and price. Under Haven Standard Clause 1, you get a flat price, written scope, and written warranty before anyone lifts a tool. No work starts without your signature.
6. 6
   Execution and documentation. We complete the agreed work, re-run the blower-door test, and hand you the before-and-after readings, installed R-values, product data sheets, and a Documented Photo Record on a USB drive.

Before

After

What Knauf Home Energy Audit Costs in Los Angeles

Most Knauf home energy audits in Los Angeles fall between $280 and $450 for homes under 2,500 square feet. Here’s what moves that number:

• Base audit (blower-door + thermal imaging + insulation inspection): $280-$340
• With duct leakage test: add $90-$110
• Homes over 2,500 square feet or with multiple HVAC zones: $380-$450
• Post-audit air sealing (if elected): $1.20-$2.80 per square foot of treated envelope, depending on access difficulty and material

We also service Reflectix radiant barrier systems, and we can assess hybrid Knauf-Reflectix installations common in Los Angeles garage-to-ADU conversions. Every estimate is free, every price is written, and every job gets the 365-Day Done Right Promise. Call (628) 226-1097 for yours.

Why Los Angeles Homeowners Call Topside Attic Insulation Los Angeles for Knauf Work

We’ve sealed and insulated over 9,000 homes since 2016, and we’ve learned that Knauf products perform well when the prep work is honest. We don’t blow insulation over unsealed attic floors. We don’t skip the blower-door test because the customer can’t see it. Wes Okafor, our owner and lead technician, learned the trade at Richard J. Daley College’s HVAC and building science programs before spending two decades in attics - including enough retrofits in Leimert Park to know that unvented knee walls and bypassed soffit chases are still standard issue in Los Angeles’s 1950s-1970s housing stock. Our materials come from Owens Corning, Johns Manville, Knauf, Rockwool, and others - no proprietary lock-in means we specify what’s right for your assembly, not what moves our inventory. Seal the holes first. Then measure the R-value. In that order.

FAQs